Reconditioned Gearbox Actuator 309105236R
We supply fully reconditioned gearbox actuators for commercial vehicles. In addition, every unit is 100% bench-tested before dispatch. Specifically, we carefully measure clutch position, engagement points, selection positions, hydraulic pressure drops, clutch progression, and slip points. As a result, you receive a highly reliable unit complete with full test report results.
Furthermore, we strongly recommend replacing the hydraulic fluid during installation. You can purchase the recommended fluid directly here: ELF Speedmatic 1L Hydraulic Oil.
Vehicle Compatibility
This actuator fits several popular commercial van models. For example, it is fully compatible with the following vehicles:
- RENAULT MASTER II – 2.5 dCi
- RENAULT TRAFIC II – 2.0 dCi / 2.5 dCi
- OPEL / VAUXHALL VIVARO – 2.0 CDTI / 2.5 CDTI
- OPEL / VAUXHALL MOVANO – 2.5 CDTI / dCi
- NISSAN PRIMASTAR – 2.0 dCi / 2.5 dCi
- NISSAN INTERSTAR – 2.5 dCi
However, please note that it fits only PA0 and PK0 semi-automatic transmissions.
Compatible OEM Part Numbers
In addition, this actuator replaces multiple original manufacturer part numbers:
- 309105236R
- 309100043R
- 309101331R
- 8200617985
- 8200983194
- 8200831969
- 8200912223
- 8200104609
Resolved Diagnostic Fault Codes
Moreover, installing this unit resolves typical transmission error codes. Below is the list of supported fault codes:
- DF068 / P0805 – Clutch Position Sensor Circuit
- DF069 / P0914 – Selection Position Sensor Circuit
- DF070 / P0904 – Engagement Position Sensor Circuit
- DF071 / P0750 – Clutch Solenoid Valve Circuit
- DF072 / P0755 – Engagement Solenoid Valve 1 Circuit
- DF073 / P0760 – Engagement Solenoid Valve 2 Circuit
- DF074 / P0765 – Selection Solenoid Valve 1 Circuit
- DF075 / P0770 – Selection Solenoid Valve 2 Circuit
- DF076 / P0901 – Clutch Control Fault
- DF077 / P2711 – Gearbox Servo Control
- DF078 / P0944 – Hydraulic Servo Control
- DF166 / P0932 – Pressure Sensor Circuit
- DF173 / C401 – Injection Multiplex Coherency
- DF180 / P1710 – Hydraulic Pump Circuit
- DF181 / P0919 – Gear Selection Impossible
- DF183 / C140 – No UCH Multiplex Signal
- DF185 / C121 – No ABS / ESP Multiplex Signal
- DF187 / P0949 – Programming / Learning Required
- DF225 / P0613 – Control Unit EEPROM Fault
- DF229 / C500B – Invalid ABS Signal
- DF233 / P1730 – Computer Error
Exchange Terms and Surcharge
We sell this product on an exchange basis. Therefore, returning your old robot unit is required.
First, a core deposit of €175 is required before shipping. Alternatively, you can send your old unit first to avoid paying the surcharge deposit.
Fitting and Adaptation Guidelines
This part is not plug-and-play. Consequently, proper diagnostic adaptation is mandatory upon installation.
To begin with, flush and purge the sequential fluid system completely using fresh ELF Speedmatic oil. Next, verify that engine coolant temperature is above 80°C and parameter PR095 is below 180°C. Perform 6 smooth accelerations at half-load over 50–100 meters to adapt clutch progression. Finally, clear all stored fault memory before starting the final road test.
This post is also available in:
Beoordelingen
Er zijn nog geen beoordelingen.